Skip to main content

Posts

Showing posts with the label Description

LM1875 AUDIO AMPLIFIER 20W

LM1875general description:

The LM1875 is a monolithic power amplifier offering very low distortion and high quality performance for consumer audio applications. The LM1875 delivers 20 watts into a 4Ω or 8Ω load on ±25V supplies. Using an 8Ω load and ±30V supplies, over 30 watts of power may be delivered. The amplifier is designed to operate with a minimum of external components. Device overload protection consists of both internal current limit and thermal shutdown.The LM1875 design takes advantage of advanced circuit techniques and processing to achieve extremely low distortion levels even at high output power levels. Other outstanding features include high gain, fast slew rate and a wide power bandwidth, large output voltage swing, high current capability, and a very wide supply range. The amplifier is internally compensated and stable for gains of 10 or greater.

LM1875 amplifier circuit:LM1875 power supply diagram: LM1875 pcb layout: LM1875 project review

LX1720 Audio Amplifier 2x20W

LX1720 general description:The LX1720 controller IC contains the necessary functions to implement a stereo Class-D audio amplifier. A Class-D amplifier is a "switching" amplifier that converts a low-level, analog, audio input signal into a highpower, pulse-width modulated (PWM) output. The switching frequency is much higher than the audio band which allows high frequency out-of-band components to be removed with a simple LC filter. The LX1720 generates a PWM output by controlling external MOSFET's connected in a full-bridge configuration. Because the MOSFET's are either full "on" or full "off", their power dissipation is minimal allowing maximum power to be delivered to the speaker.
LX1720 Circuit:

TDA8922 Audio Amplifier 2x25W

TDA8922general description:
The TDA8922 is a high efficiency class-D audio power amplifier with very low dissipation. The typical output power is 2 × 25 W. The device is available in the HSOP24 power package with a small internal heatsink and in the DBS23P through-hole power package. Depending on the supply voltage and load conditions, a very small or even no external heatsink is required. The amplifier operates over a wide supply voltage range from ±12.5 to ±30 V and consumes a very low quiescent current.

TDA8922 features:
High efficiency (∼90%)Operating supply voltage from ±12.5 to ±30 VVery low quiescent currentLow distortionUsable as a stereo Single-Ended (SE) amplifier or as amono amplifier in Bridge-Tied Load (BTL)Fixed gain of 30 dB in Single-Ended (SE) and 36 dB inBridge-Tied Load (BTL)High output powerGood ripple rejectionInternal switching frequency can be overruled by an external clockNo switch-on or switch-off plop noiseShort-circuit proof across load and to supply linesElect…

TDA7490 Audio Amplifier 2x25W

TDA7490general description: The TDA7490 is a dual audio class D amplifier assembled in Flexiwatt 25 package; it is specially designed for high efficiency application mainly for TV and Home Stereo sets.

TDA7490 features: 
25W + 25W OUTPUT POWER:RL = 8Ω/4Ω; THD = 10%HIGH EFFICIENCYWIDE SUPPLY VOLTAGE RANGE (FROM±10 TO ±25V)SPLIT SUPPLYTURN OFF/ON POP FREEST-BY AND MUTE FEATURESSHORT CIRCUIT PROTECTION ACROSSTHE LOADTHERMAL OVERLOAD PROTECTIONEXTERNALLY SINCHRONIZABLEBRIDGE CONFIGURATION
TDA7490 amplifier diagram, circuits:


TDA7490 layout, pcb:


STK4221 Audio Amplifier 2x80w

STK4221general description: The STK4221II IC from SANYO is a dual high power amplifier chip, preferably suited for compact high power audio applications, for example in cars and luxury transport vehicle audio systems. The chip provides a hassle free stereo output through a single package and a hand full of few external components, making the construction of this circuit rather easy and straightforward. However since the idea presented here does not include a CD or a memory card driver circuit, the input may be derived from readymade audio sources like an ipod, CD walkman, cellphone etc. The circuit discussed here is intended specifically for car audio applications and provides a simple alternative for  making a 100 watt car stereo amplifier circuit. The diagram may be understood with the following points: An RC network formed by R5, R6 and C3, C4 together helps to reduce and filter stray frequency interferences and is therefore included at the input of the amplifiers. Capacitors C5 and …

TDA1015 Audio Amplifier 1x4W

TDA1015general description:

The TDA1015 is a monolithic integrated audio amplifier circuit in a 9-lead single in-line (SIL) plastic package. The device is especially designed for portable radio and recorder applications and delivers up to 4 W in a 4Ω load impedance. The very low applicable supply voltage of 3,6 V permits 6 V spplications.
TDA1015 features:

single in-line (SIL) construction for easy mountingseparated preamplifier and power amplifierhigh output powerthermal protectionhigh input impedancelow current drainlimited noise behaviour at radio frequencies
TDA1015 reference data:

Supply voltage range VP 3,6 to 18 VPeak output current IOM max. 2,5 AOutput power at dtot= 10%VP = 12 V; RL = 4 Ω Po typ. 4,2 WVP = 9 V; RL = 4 Ω Po typ. 2,3 WVP = 6 V; RL = 4 Ω Po typ. 1,0 WTotal harmonic distortion at Po = 1 W; RL = 4 Ω dtot typ. 0,3 %Input impedance preamplifier (pin 8) |Zi | > 100 kΩ power amplifier (pin 6) |Zi| typ. 20 kΩTotal quiescent current Itot typ. 14 mAOperating ambient temperat…

TDA7490 Audio Amplifier 2 x 25W / 1 x 50W

TDA7490general description:
The TDA7490 is a dual audio class D amplifier assembled in Flexiwatt 25 package; it is specially designed for high efficiency application mainly for TV and Home Stereo sets. TDA7490 Audio Amplifier 2 x 25W / 1 x 50W

TDA7490 features:25W + 25W OUTPUT POWER:RL = 8Ω/4Ω; THD = 10%HIGH EFFICIENCYWIDE SUPPLY VOLTAGE RANGE (FROM±10 TO ±25V)SPLIT SUPPLYTURN OFF/ON POP FREEST-BY AND MUTE FEATURESSHORT CIRCUIT PROTECTION ACROSSTHE LOADTHERMAL OVERLOAD PROTECTIONEXTERNALLY SINCHRONIZABLEBRIDGE CONFIGURATION

TDA7490 sterio circuit diagram: TDA7490 mono circuit diagram:

TDA7490 sterio circuit pcb:

TDA1562Q Audio Amplifier 50W

 TDA1562Qgeneral description: Philips designers have further improved a number of properties of the IC, among which the power output. According to the Philips datasheet, the improved device, the TDA1562Q, can deliver 70 watts into 4 ohms, but that is at the cost of the distortion, which at 10 per cent is rather too high, even for in a car. The prototype of the design described in this article provides 54 watts into 4 ohms at 1 per cent distortion. Since the number of requisite external components is smaller than in the case of the earlier device, the printed-circuit board is even more compact than that for the February 1995 amplifier.

 TDA1562Q features:
Low power dissipation during reproduction of music signalsProof against short-circuitsProtection against excessive temperaturesStandby switchNo power-on or power-off clicksVisible error indicationMeasurement results (at Ub=14.4 V)Supply voltage 8–18 VSensitivity 760 mV r.m.s.Input impedance 70 kΩPower output 54 W r.m.s. into 4 Ω (f=1 kHz…

TDA7560 Audio Amplifier 4x50W

TDA7560general description:

TDA7560 is a 4 x 45W QUAD BRIDGE car audio amplifier plus HSD. The TDA7560’s inputs are ground-compatible and can stand very high input signals (± 8Vpk) without any performances degradation. If the standard value for the input capacitors (0.1mF) is adopted, the low frequency cut-off will amount to 16 Hz. The TDA7560 is a breakthrough BCD (Bipolar / CMOS / DMOS) technology class AB Audio Power Amplifierin Flexiwatt 25 package designed for high power car radio. The fully complementary P-Channel/N-Channel output structure allows a rail to rail output voltage swing which, combined with high output current and minimised saturation losses sets new power references in the car-radio field, with unparalleled distortion performances.
TDA7560 features: 4 x 50W/4W MAX.4 x 45W/4W EIAJ4 x 30W/4W @ 14.4V, 1KHz, 10%4 x 80W/2W MAX.4 x 77W/2W EIAJ4 x 55W/2W @ 14.4V, 1KHz, 10%EXCELLENT 2W DRIVING CAPABILITYHI-FI CLASS DISTORTIONLOW OUTPUT NOISETDA7560 amplifier circuit diagram: T…

TDA8922 Audio Amplifier 2 x 25W

TDA8922general description:

The TDA8922 is a high efficiency class-D audio power amplifier with very low dissipation. The typical output power is 2 × 25 W. The device is available in the HSOP24 power package with a small internal heatsink and in the DBS23P through-hole power package. Depending on the supply voltage and load conditions, a very small or even no external heatsink is required. The amplifier operates over a wide supply voltage range from ±12.5 to ±30 V and consumes a very low quiescent current. TDA8922 Audio Amplifier 2 x 25W

TDA8922 features:
High efficiency (∼90%)Operating supply voltage from ±12.5 to ±30 VVery low quiescent currentLow distortionUsable as a stereo Single-Ended (SE) amplifier or as a mono amplifier in Bridge-Tied Load (BTL) Fixed gain of 30 dB in Single-Ended (SE) and 36 dB in Bridge-Tied Load (BTL)High output powerGood ripple rejectionInternal switching frequency can be overruled by an external clockNo switch-on or switch-off plop noiseShort-circuit proof ac…

TDA7482 Audio Power Amplifier 1-channel 1 x 25W

TDA7482general description:

The TDA7482 is an audio class-D amplifier assembled in Multiwatt15 package specially designed for high efficiency applications mainly for TV and HomeStereo sets. TDA7482 Audio Amplifier 1 x 25W TDA7482 features:

25W OUTPUT POWER:RL =8Ω/4Ω; THD = 10%HIGHEFFICIENCYWIDE SUPPLY VOLTAGE RANGE (UP TO±25V)SPLITSUPPLYOVERVOLTAGEPROTECTIONST-BY AND MUTEFEATURESSHORTCIRCUIT PROTECTIONTHERMALOVERLOADPROTECTIONTDA7482 circuit diagram:
TDA7482 sterio circuit layout:

LM386N Audio Power Amplifer Amplifier 1x2W

LM386N general description:


The LM386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but the addition of an external resistor and capacitor between pins 1 and 8 will increase the gain to any value up to 200. The inputs are ground referenced while the output is automatically biased to one half the supply voltage. The quiescent power drain is only 24 milliwatts when operating from a 6 volt supply, making the LM386 ideal for battery operation. LM386N Audio Amplifier 1x2W
LM386N features:Battery operationMinimum external partsWide supply voltage range: 4V–12V or 5V–18VLow quiescent current drain: 4mAVoltage gains from 20 to 200Ground referenced inputSelf-centering output quiescent voltageLow distortion: 0.2% (AV = 20, VS = 6V, RL = 8Ω, PO =125mW, f = 1kHz)n Available in 8 pin MSOP package
LM386N circuit diagram: LM386N layout: LM386N pin layout:

TDA1566 Audio Amplifier 2x46W / 1x92W

TDA1566general description:

The TDA1566 is a car audio power amplifier with a complementary output stage realized in BCDMOS. The TDA1566 has two Bridge Tied Load (BTL) output stages and comes in a HSOP24 or DBS27P package. The TDA1566 can be controlled with or without I2C-bus. With I2C-bus control gain settings per channel and diagnostic trigger levels can be selected. Failure conditions as well as load identification can be read with I2C-bus. The load identification detects whether the outputs of a BTL channel are connected with a DC or AC load and discriminates between a speaker load, a line driver load and an open (unconnected) load. The TDA1566 can be configured in a single BTL mode and drive a 1 Ω load. For the single BTL mode it is necessary to connect on the Printed-Circuit Board (PCB) the outputs of both BTL channels in parallel.  TDA1566 Audio Amplifier 2x46W / 1x92W
TDA1566 features:
Operates in I2C-bus mode and non-I2C-bus modeTH version: four I2C-bus addresses controlled by two p…