Skip to main content

TDA2030 Audio Amplifier 1 x40W

TDA2030 general description: 

    Although there are a number of hybrid output modules on the market, very few of them combine compactness with reasonable price and good performance. One of these few is SGS's used in the present amplifier. The design of the amplifier is straightforward: a power op-amp followed by two output transistors. The audio signal is applied to the non-inverting input of power op-amp IC1 TDA2030 via socket K1 and capacitor C1. The supply current to the IC varies in accordance with the input signal. Consequently, there will be a similarly varying voltage drop across resistors R6, R7, R8, and R9 since these are in the supply lines to the op-amp. As long as the current is lower than about 1A, the voltage drop across the resistors will be insufficient to switch on transistors T1 and T2. This means that outputs up to 2 W into 4 ohm are provided entirely by the op-amp. Once the output current exceeds a level of 1A, the transistors are on and contribute to the power output.
When the Input signal is small, there no quiescent current through the transistor, but there is through the op-amp. Crossover problems are thus obviated. Since the IC also provides thermal compensation, stability of the operating point is ensured.
The supply voltage may lie between 12 V and an absolute maximum of 44 V. Construction of the amplifier on the printed-circuit board should be straightforward. The transistors as well as the IC must be fitted insulated on to a heat sink of about 2 k W. Use plenty of heat conducting paste. The supply line should be protected by a 3.15 A fuse. You can use BD911, BD912 for T1 and T2.

TDA2030 Technical Data:

  • Supply voltage  - 44 V
  • Maximum output - 22 W into 8 Ohm
  • Maximum output - 44 W into 4 Ohm

TDA2030 Circuit diagram:

TDA2030 circuit diagram

TDA2030 pcb layout:

TDA2030 pcb and layout

TDA2030 parts list:

  • R1-R4 - 100 KOhm
  • R5 - 8.2 KOhm
  • R6 - R9 - 1.4 Ohm, 1%
  • R10 - 1 Ohm

  • C1 - 470 nF
  • C2 - 10 uF, 63 V, radial
  • C3 - 4.7uF, 63 V, radial
  • C4,C5,C7 - 220 nF
  • C6 - 2200 uF, 50 V, radial
  • C8 - 100 uF, 50 V, radial

  • D1, D2 - 1N4001
  • T1 - BD712
  • T2 - BD711
  • IC1 - TDA2030
Datasheet for TDA2030: Download

Searches related to TDA2030

tda2030 circuit,
tda2030 power supply,
tda2030 subwoofer amplifier circuit,
tda2030 pinout,
tda2030 ic,
tda2030 price,
tda2030 pdf,
tda2030 pin configuration,


  1. value of R1, R2, R3 and R4????????????

    1. Sorry, added R1-R4 - 100 KOhm, but you can see tje value on the circuit :)...

    2. R1, R2 It is better to use a nominal value of 10 - 20 kOhm, otherwise the charging time of the capacitor C2 will be too long!

    3. Sorry R2 and R3 10 - 20 k

  2. in place of bd711/bd712, you can use tip41C/TIP42C, they have slightly lower elect. char. though

  3. -44 supply? i don't get it. i think it will destroy the IC. because as far as i know maximum supply for tda 2030 is -+25V. So pls post here how this circuit works.

    1. tda2030 : max +- 18 or one supply + 36 v and GND , 44v its for the Atda2030 who is capable of 44 v or +- 22 .

  4. Thank you so much for sharing this datasheet to us, and I also find all kinds of pdf on the electronic components online shop, I hope it will help you.


Post a Comment

Popular posts from this blog

200W Subwoofer Amplifier Circuit

Circuit Description
Here is a circuit that uses a mosfet amplifier amplicable for subwoofer as the main booster, or the basis of this boosterAmplifier. Circuit which uses MOSFET Power Amplifier is powered by the output more than 200W Speaker 8 Ohm impedance. We also include a suitable power supply circuit with the use of MOSFETamplifier with 200W of power, not only of his course Schematic diagram for the layout design is also already there.
Amplifier Circuit Diagram
200W Mosfet Amplifier LAyout PCB
Regulator Circuit Diagram MOSFET AMPLIFIER Regulator PCB MOSFET amplifier

TDA7294 Audio Amplifier 2 x 80W

TDA7294 general description:
This circuit described here uses two cis tda 7294 for use in stereo (2 x 80Watts) or bridge mode (1x 180 Watts), to configure this setting just four jumpers. To facilitate mounting the circuit has power supply attached. The power is kind of simple symmetrical with a bridge rectifier 6A, and two large electrolytic capacitors , 10000μF the 22000μF/50v. This Power supply will for the two modules. The processor is recommended 22-0-22 to 28-0-28 / 5A, depending on the quality of the transformer is recommended at least 6 amps of current.

TDA7294 features:
High power performances with limited supply voltage level.Considerably high output power even with high load values (i.e. 16 Ohm).Rl= 8 Ohm, Vs = ±25V Pmax = 150 WRl=16Ohm, Vs = ±35V 
TDA7294 circuit diagram:

TDA7294 layout:TDA7294 pcb:

Datasheet for TDA7294:Download
Searches related to TDA7294 Audio Amplifier Circuits tda7294 bridge amplifier circuit ic tda7294 subwoofer tda7294 subwoofer schematic tda7294 single suppl…