Skip to main content

Car Subwoofer Amplifier Circuit Diagram

Circuit Description:
This unit is intended to be connected to an existing car stereo amplifier, adding the often required extra “punch” to the music by driving a subwoofer. As very low frequencies are omnidirectional, a single amplifier is necessary to drive this dedicated loudspeaker. The power amplifier used is a good and cheap BTL (Bridge Tied Load) 13 pin IC made by Philips (now NXP Semiconductors) requiring a very low parts count and capable of delivering about 22W into a 4 Ohm load at the standard car battery voltage of 14.4V.
The stereo signals coming from the line outputs of the car radio amplifier are mixed at the input and, after the Level Control, the signal enters the buffer IC1A and can be phase reversed by means of SW1. This control can be useful to allow the subwoofer to be in phase with the loudspeakers of the existing car radio. Then, a 12dB/octave variable frequency Low Pass filter built around IC1B, Q1 and related components follows, allowing to adjust precisely the low pass frequency from 70 to 150Hz. Q2, R17 and C9 form a simple dc voltage stabilizer for the input and filter circuitry, useful to avoid positive rail interaction from the power amplifier to low level sections.

Circuit diagram:
Parts circuit:

P1_____________10K Log Potentiometer
P2_____________22K Dual gang Linear Potentiometer
R1,R4___________1K 1/4W Resistors
R2,R3,R5,R6____10K 1/4W Resistors
R7,R8_________100K 1/4W Resistors
R9,R10,R13_____47K 1/4W Resistors
R11,R12________15K 1/4W Resistors
R14,R15,R17____47K 1/4W Resistors
R16_____________6K8 1/4W Resistor
R18_____________1K5 1/4W Resistor
C1,C2,C3,C6_____4µ7 25V Electrolytic Capacitors
C4,C5__________68nF 63V Polyester Capacitors
C7_____________33nF 63V Polyester Capacitor
C8,C9_________220µF 25V Electrolytic Capacitors
C10___________470nF 63V Polyester Capacitor
C11___________100nF 63V Polyester Capacitor
C12__________2200µF 25V Electrolytic Capacitor
D1______________LED any color and type
Q1,Q2_________BC547 45V 100mA NPN Transistors
IC1___________TL072 Dual BIFET Op-Amp
IC2_________TDA1516BQ 24W BTL Car Radio Power Amplifier IC
SW1____________DPDT toggle or slide Switch
SW2____________SPST toggle or slide Switch capable of withstanding a current of at least 3A
J1,J2__________RCA audio input sockets
SPKR___________4 Ohm Woofer or two 8 Ohm Woofers wired in parallel

Technical data:

Output power (1KHz sinewave):
22W RMS into 4 Ohms at 14.4V supply
Sensitivity:
250mV input for full output
Frequency response:
20Hz to 70Hz -3dB with the cursor of P2 fully rotated towards R12
20Hz to 150Hz -3dB with the cursor of P2 fully rotated towards R11
Total harmonic distortion:
17W RMS: 0.5% 22W RMS: 10%
Original article sourse: eeweb.com

Searches related to car subwoofer amplifier circuit diagram
car subwoofer amplifier circuit diagram pdf
subwoofer circuit diagram free download
la4440 subwoofer circuit
5.1 subwoofer circuit diagram
low pass subwoofer circuit diagram
transistor subwoofer circuit diagram
subwoofer circuit diagram pdf
4558 ic subwoofer circuit


Comments

Popular posts from this blog

200W Subwoofer Amplifier Circuit

Circuit Description
Here is a circuit that uses a mosfet amplifier amplicable for subwoofer as the main booster, or the basis of this boosterAmplifier. Circuit which uses MOSFET Power Amplifier is powered by the output more than 200W Speaker 8 Ohm impedance. We also include a suitable power supply circuit with the use of MOSFETamplifier with 200W of power, not only of his course Schematic diagram for the layout design is also already there.
Amplifier Circuit Diagram
200W Mosfet Amplifier LAyout PCB
Regulator Circuit Diagram MOSFET AMPLIFIER Regulator PCB MOSFET amplifier

TDA7294 Audio Amplifier 2 x 80W

TDA7294 general description:
This circuit described here uses two cis tda 7294 for use in stereo (2 x 80Watts) or bridge mode (1x 180 Watts), to configure this setting just four jumpers. To facilitate mounting the circuit has power supply attached. The power is kind of simple symmetrical with a bridge rectifier 6A, and two large electrolytic capacitors , 10000μF the 22000μF/50v. This Power supply will for the two modules. The processor is recommended 22-0-22 to 28-0-28 / 5A, depending on the quality of the transformer is recommended at least 6 amps of current.


TDA7294 features:
High power performances with limited supply voltage level.Considerably high output power even with high load values (i.e. 16 Ohm).Rl= 8 Ohm, Vs = ±25V Pmax = 150 WRl=16Ohm, Vs = ±35V 
TDA7294 circuit diagram:

TDA7294 layout:TDA7294 pcb:

Datasheet for TDA7294:Download
Searches related to TDA7294 Audio Amplifier Circuits tda7294 bridge amplifier circuit ic tda7294 subwoofer tda7294 subwoofer schematic tda7294 single suppl…

TDA2030 Audio Amplifier 1 x40W

TDA2030 general description:    Although there are a number of hybrid output modules on the market, very few of them combine compactness with reasonable price and good performance. One of these few is SGS's used in the present amplifier. The design of the amplifier is straightforward: a power op-amp followed by two output transistors. The audio signal is applied to the non-inverting input of power op-amp IC1 TDA2030 via socket K1 and capacitor C1. The supply current to the IC varies in accordance with the input signal. Consequently, there will be a similarly varying voltage drop across resistors R6, R7, R8, and R9 since these are in the supply lines to the op-amp. As long as the current is lower than about 1A, the voltage drop across the resistors will be insufficient to switch on transistors T1 and T2. This means that outputs up to 2 W into 4 ohm are provided entirely by the op-amp. Once the output current exceeds a level of 1A, the transistors are on and contribute to the power …