Skip to main content

Power Amplifier 60 Watt supply voltage 30 - 60 Volts


Power Amplifier 60 Watt supply voltage 30 - 60 Volts


This is a simple and low cost 60W power amplifier. The optimal supply voltage is around 50V, but this amp can work from 30 to 60V. The maximum input voltage is around 0.8 - 1V. As you can see, in this design the components have a big tolerance, so you can build it with almost any components that you can find at home. The output power transistors can be any NPN types, but do not use Darlington types.

Capacitor C1 regulates the low frequencies (bass), as the capacitance grows, the low frequencies are getting louder. Capacitor C2 regulates the higher frequencies (treble), as the capacitance grows, the higher frequencies are getting quieter. 

This is a class B amplifier, this means, that a current must flow through the end transistors, even if there is no signal on the input. This current can be regulated with the 500 Ohm trimmer resistor. As this current increases, the sound of the amplifier is better, but output transistors are dispatching more heat. If the current is decreased, the transistors are dispatching less heat, but the sound quality is decreased.

Power Amplifier 60 Watt supply voltage 30 - 60 Volts

Comments

Popular posts from this blog

200W Subwoofer Amplifier Circuit

Circuit Description
Here is a circuit that uses a mosfet amplifier amplicable for subwoofer as the main booster, or the basis of this boosterAmplifier. Circuit which uses MOSFET Power Amplifier is powered by the output more than 200W Speaker 8 Ohm impedance. We also include a suitable power supply circuit with the use of MOSFETamplifier with 200W of power, not only of his course Schematic diagram for the layout design is also already there.
Amplifier Circuit Diagram
200W Mosfet Amplifier LAyout PCB
Regulator Circuit Diagram MOSFET AMPLIFIER Regulator PCB MOSFET amplifier

TDA7294 Audio Amplifier 2 x 80W

TDA7294 general description:
This circuit described here uses two cis tda 7294 for use in stereo (2 x 80Watts) or bridge mode (1x 180 Watts), to configure this setting just four jumpers. To facilitate mounting the circuit has power supply attached. The power is kind of simple symmetrical with a bridge rectifier 6A, and two large electrolytic capacitors , 10000μF the 22000μF/50v. This Power supply will for the two modules. The processor is recommended 22-0-22 to 28-0-28 / 5A, depending on the quality of the transformer is recommended at least 6 amps of current.


TDA7294 features:
High power performances with limited supply voltage level.Considerably high output power even with high load values (i.e. 16 Ohm).Rl= 8 Ohm, Vs = ±25V Pmax = 150 WRl=16Ohm, Vs = ±35V 
TDA7294 circuit diagram:

TDA7294 layout:TDA7294 pcb:

Datasheet for TDA7294:Download
Searches related to TDA7294 Audio Amplifier Circuits tda7294 bridge amplifier circuit ic tda7294 subwoofer tda7294 subwoofer schematic tda7294 single suppl…

TDA2030 Audio Amplifier 1 x40W

TDA2030 general description:    Although there are a number of hybrid output modules on the market, very few of them combine compactness with reasonable price and good performance. One of these few is SGS's used in the present amplifier. The design of the amplifier is straightforward: a power op-amp followed by two output transistors. The audio signal is applied to the non-inverting input of power op-amp IC1 TDA2030 via socket K1 and capacitor C1. The supply current to the IC varies in accordance with the input signal. Consequently, there will be a similarly varying voltage drop across resistors R6, R7, R8, and R9 since these are in the supply lines to the op-amp. As long as the current is lower than about 1A, the voltage drop across the resistors will be insufficient to switch on transistors T1 and T2. This means that outputs up to 2 W into 4 ohm are provided entirely by the op-amp. Once the output current exceeds a level of 1A, the transistors are on and contribute to the power …