Skip to main content

Mono audio panoramic interference

The circuit spectator interference enables implantation mono sound at any point between stereo speakers. When P1 is in the middle of his journey, there is strengthening or weakening of the mark the entrance to the exit in any of the two channels. When the potentiometer placed elsewhere, away from halfway, the signal in one channel is supported 3dB more than the other. The input stage is a buffer (IC1). Inverts the input signal to ensure compliance with this phase of the output (Next steps' and reverse them the signal they receive to entry). The resistance value entry identifies to that of R 1 (1 A KO). The output buffer is driven in stereo amplifiers IC2 and IC3.

The potentiometer P1, in conjunction with the A3, R4, R8, and A9, affects the routes of feedback and two boosters. This result in any adjustment of P1 to make the opposite metavoles enischysi the two opamps. The series resistors A7 and A12 provide the possibility of output lead capacitive loads. Capacitors coupling C3, C6 and C9 can be omitted if the application for the intended circuit can tolerate continuous diversion trends in output of about 20-30 mv. The capacitors C2, C5 and C8 ensure stability amplifier, even with unit gain. The capacitors C 1, C4 and C7 minimize any interference r1, which is probably appears within the area 2.5IZ-200KIZ. The performance of the circuit is very good and can be used in High-quality consoles. The total harmonic distortion plus thorythoo the frequency of 1 kHz with a bandwidth of 22 kHz is 0.0014%. The circuit needs power supply 18 W of power which consumes approximately 16 mA.

 Mono audio panoramic interference
 Mono audio panoramic interference

Comments

Popular posts from this blog

200W Subwoofer Amplifier Circuit

Circuit Description
Here is a circuit that uses a mosfet amplifier amplicable for subwoofer as the main booster, or the basis of this boosterAmplifier. Circuit which uses MOSFET Power Amplifier is powered by the output more than 200W Speaker 8 Ohm impedance. We also include a suitable power supply circuit with the use of MOSFETamplifier with 200W of power, not only of his course Schematic diagram for the layout design is also already there.
Amplifier Circuit Diagram
200W Mosfet Amplifier LAyout PCB
Regulator Circuit Diagram MOSFET AMPLIFIER Regulator PCB MOSFET amplifier

TDA7294 Audio Amplifier 2 x 80W

TDA7294 general description:
This circuit described here uses two cis tda 7294 for use in stereo (2 x 80Watts) or bridge mode (1x 180 Watts), to configure this setting just four jumpers. To facilitate mounting the circuit has power supply attached. The power is kind of simple symmetrical with a bridge rectifier 6A, and two large electrolytic capacitors , 10000μF the 22000μF/50v. This Power supply will for the two modules. The processor is recommended 22-0-22 to 28-0-28 / 5A, depending on the quality of the transformer is recommended at least 6 amps of current.


TDA7294 features:
High power performances with limited supply voltage level.Considerably high output power even with high load values (i.e. 16 Ohm).Rl= 8 Ohm, Vs = ±25V Pmax = 150 WRl=16Ohm, Vs = ±35V 
TDA7294 circuit diagram:

TDA7294 layout:TDA7294 pcb:

Datasheet for TDA7294:Download
Searches related to TDA7294 Audio Amplifier Circuits tda7294 bridge amplifier circuit ic tda7294 subwoofer tda7294 subwoofer schematic tda7294 single suppl…

TDA2030 Audio Amplifier 1 x40W

TDA2030 general description:    Although there are a number of hybrid output modules on the market, very few of them combine compactness with reasonable price and good performance. One of these few is SGS's used in the present amplifier. The design of the amplifier is straightforward: a power op-amp followed by two output transistors. The audio signal is applied to the non-inverting input of power op-amp IC1 TDA2030 via socket K1 and capacitor C1. The supply current to the IC varies in accordance with the input signal. Consequently, there will be a similarly varying voltage drop across resistors R6, R7, R8, and R9 since these are in the supply lines to the op-amp. As long as the current is lower than about 1A, the voltage drop across the resistors will be insufficient to switch on transistors T1 and T2. This means that outputs up to 2 W into 4 ohm are provided entirely by the op-amp. Once the output current exceeds a level of 1A, the transistors are on and contribute to the power …