12/23/2017

200W Audio Amplifier Circuit

Leave a Comment
Circuit description:

Connecting two TDA2030 thru cheap power transistors we can create a amplifier wich can deliver a higher power. With the components value from the schematic the total amplifier gain is 32 dB. The speaker can be 2 ohm instead of 4 ohm if we use the TIP transistors. TDA 2030 is produced by SGS Ates and is a complete audio amplifier. AB class of the final amplifier cand deliver up to 14W on 4 ohm at a +-14V power supply. With a proper designed power supply this audio amplifier can output 200W.

Circuit diagram:


transistor audio amplifier circuit diagram

transistor audio amplifier circuit diagram

Part list
  • IC1, Ic2 TDA 2030
  • T1, T3 = BD 250, TIP 36
  • T2,T4 = BD 249, TIP 35
  • D1 … D4 = 1N4001


150 watt audio amplifier circuit
400w amplifier circuit diagram
200w stereo digital audio power amplifier
3055 transistor audio amplifier circuit
1000 watts amplifier circuit diagram
200 watt audio amplifier circuit diagram
4 transistor audio amplifier
transistor audio amplifier circuit diagram

Read More...

12/20/2017

Subwoofer Circuit Diagram

Leave a Comment
Circuit Descrition
The acoustic spectrum is extended by very low frequencies 20Iz and reaches as the 20000Iz in high frequencies. In the low frequencies is degraded the sense of direction. This reason us leads to the utilization speaker for the attribution of very low frequencies. The manufacture that to you we propose distinguishes these frequencies, in order to him we lead to the corresponding amplifier. The acoustic filters are met in various points in the sound systems. The knownest application they are the filters baxandal for regulating tone low and high frequencies and filters crossover where the acoustic region is separated in subareas, in order to it leads the corresponding loudspeakers. The application that to you we propose is a simple filter of region that limits the acoustic region (20-20000Hz) in the region 20-100Hz.

With the manufacture that to you we propose you can make a active filter in order to you lead a loudspeaker of very low frequencies. With this you will place one bigger speaker between the HIFI speakers of you. In order to you have a complete picture of sound you will need also the corresponding amplifier. In the entry of circuit you will connect the two exits of preamplifier or the exit of line of some preamplifier. The circuit of manufacture allocates a exit in order to is led means of circuit of force subwoofer. If for some reason you do not have space in order to you place the third speaker in space of hearing, then you can select smaller speaker. The output will depend from the type of music that you hear. If in deed you have space, then after you make a filter and remain thanked, you can him recommend in your friends or still make other same for your friends.


Circuit Diagram



In the form it appears the theoretical circuit of filter. In first glance we see three different circuits that are mainly manufactured round two operational amplifiers. This circuits constitute mixed, amplifier with variable aid and a variable filter. The manufacture end needs a circuit of catering with operational tendency of catering equal with ±12. the operational amplifiers that constitute the active elements for this circuits of are double operational type as the TL082 and NE5532. The operational these amplifiers belong in a family provided with transistor of effect of field IFET in their entries. Each member of family allocates in their circuit bipolar transistor and effect of field. This circuits can function in his high tendency, because that they use transistor of high tendency. Also they have high honor of rhythm of elevation (slew rate), low current of polarization for the entries and are influenced little by the temperature. The operational these amplifiers have breadth of area unity gain bandwidth 3MHz. A other important element for their choice is the big reject of noise, when this exists in the line of catering.

The price of reject is bigger than 80dB, their consumption is small, from 11 until 3 mA. They are internally sold in nutshell with eight pins and allocate two operational amplifiers, In the same line in nutshell 14 pins they incorporate four operational, In the trade they are sold with code TL074, TL084 and TL064, In nutshell with eight pins they are sold operational amplifiers TL061 TL071 kajTL081. In the manufacture we used the TL082 that has two operational. First operational from the TL082 it works as amplifier and mixed for the two channels, In his negative entry he exists one small mixed with two resistances. A potentiometer in this rung determines the aid of circuit. In the point this left winger and the right channel of preamplifier they are added means of two resistances. En continuity the operational strengthens signal with aid made dependent from the price that has the potentiometer.

The place of runner is proportional with the aid of circuit. The second operational amplifier is the filter of manufacture. The filter of is acoustic frequency of second class and he is made with the materials that are round the operational amplifier. The filter of is low passage with variable frequency of cutting off. This frequency can be altered and take prices from very low frequency the 30Hz or still exceed 150Hz. The frequency of cutting off of filter depends from the prices that have the elements of circuit. Altering the values of elements we can have frequency of cutting off 150Iz, 130Iz, J00Iz, 7Ïz, 6Íz even 3Íz, this prices they can be achieved with the simple rotation of double potentiometer. The circuit of filter has been made around one operational' that it has completed TL082 that is double operational amplifier. In the exit of filter we will link the plug of expense where is connected the amplifier. In the exit of circuit is presented, the limited as for the breadth of frequencies, signal that we apply in the entry of circuit.

Parts

R1 = 39 Kohm
R2 = 39 Kohm
R3 = 47 Kohm
R4 = 10 Ohm
R5 = 22 Kohm
R6 = 4,7 Kohm
R7 = 22 Kohm
R8 = 4,7 Kohm
R9 = 10 Ohm
R10 = 220 Ohm
C1 = 39 pF
C2 = 0.1 uF
C3 = 0.1 uF
C4 = 0.2 uF
C5 = 0.4 uF
C6 = 0.1 uF
C7 = 0.1 uF
IC1 = TL064

PCB and layout


In order to you make the manufacture you will need printed that appears in the form. In this you will place the materials according to the following form. The materials are enough also easy can become certain errors. With few attention however you can him avoid. If they are presented difference malfunctions, you check carefully the circuit. The circuit, as we said, is filter and it should they are used materially good precision and quality, particularly for the capacitors. The capacitors of filters will have tolerance 5%. Of course, the manufacture will also work with material of lower quality, the trial of manufacture can become with acoustic signal of generator We apply the generator in the entry of manufacture and we measure with a voltmeter the tendency in the exit of filter. If we alter the potentiometer and are altered the tendency, then all have well.

Original article sourse: diy-electronic-projects.com

subwoofer circuit diagram pdf
12v subwoofer circuit diagram
subwoofer circuit diagram free download
4558 ic subwoofer circuit
la4440 subwoofer circuit
transistor subwoofer circuit diagram
low pass subwoofer circuit diagram
5.1 subwoofer circuit diagram

Read More...

12/19/2017

100W MOSFET power amplifier

Leave a Comment
Circuit Description:
MOSFET power amplifier circuit based on IRFP240 and IRFP9240 MOSFETs is shown here. The amplifier operates from a +45/-45 V DC dual supply and can deliver 100 watt rms into an 8 ohm speaker and 160 watt rms into a 4 ohm speaker. This Hi-Fi amplifier circuit is suitable for a lot applications like general purpose amplifier, guitar amplifier, keyboard amplifier. The amplifier can be also used as a sub woofer amplifier but a subwoofer filter stage has to be added before the input stage. The amplifier has a low distortion of 0.1%, a damping factor greater than 200, input sensitivity of 1.2V and the bandwidth is from 4Hz to 4 KHz.

Circuit Features:
  • Assemble the circuit on a good quality PCB.
  • Use a +45/-45 V DC, 3A dual supply for powering the circuit.
  • Power supply voltage must not exceed +55/-55 V DC.
  • Before connecting the speaker, check the zero signal output voltage of the amplifier and in any case it should not be higher than 50mV. If it is higher than 50mV, check the circuit for any error. Replacing Q1, Q2 with another set could also solve the problem.
  • Fit Q7 and Q8 to a 2°C/W heat sink. Both Q7 and Q8 must be isolated from the heat sink using mica sheets. Heat sink mounting kits for almost all power transistors/ MOSFETs of almost all package styles are readily available in the market.
  • All resistors other than R10, R11 and R19 are 1/4 watt metal film resistors. R10 and R11 are 5W wire wound type while R19 is a 3W wire wound type.
Circuit Diagram:
100W MOSFET power amplifier
100W MOSFET power amplifier

Searches related to 100W MOSFET power amplifier
irfp250 mosfet amplifier
mosfet power amplifier circuit
200 watt mosfet amplifier circuit
12v mosfet amplifier circuit
mosfet amplifier circuit for subwoofer
mosfet power amplifier pdf
irfp240 irfp9240 amplifier
simple mosfet amplifier circuit

Read More...

300W Subwoofer Power Amplifier

Leave a Comment
This is an amplifier circuit that is formed from a transistor amplifier miraculous. This circuit is used in the speaker subwoofer with 300W maximum power on each side. To apply it, can be used in the room that is not too large, like the car. And the voltage needed between 25 to 42 Volt DC.
300W Subwoofer Power Amplifier
300W Subwoofer Power Amplifier
Searches related to 300W Subwoofer Power Amplifier
200w subwoofer amplifier circuit diagram
subwoofer circuit diagram free download
300w subwoofer amplifier circuit diagram
low pass subwoofer circuit diagram
12v subwoofer circuit diagram
500w audio amplifier circuit diagram pdf
subwoofer circuit diagram pdf
500w power amplifier circuit diagram datasheet
Read More...

12/12/2017

Mosfet Amplifier Circuit for Subwoofer 400W

Leave a Comment
Power amp 400W IRFP448 Circuit
Amplifier circuit today,We would like to show you for the MOSFET 400 watt amplifier is amplifier on my kW shares the same circuit and basic PCB layout.
The only real difference is the number of output devices to the device.
We have using The IRFP448 design while the MOSFET amplifier 14 O / P devices.
These amplifiers can be used for virtually any application that requires high performance, low use Noise, distortion and excellent sound quality. Examples would be subwoofer amplifier should FOH stage
Amplifiers, surround a canal a very powerful sound amplifier, etc.
The 400W MOSFET-amplifier has four key stages of amplification. We are looking to start any Phase appropriate detail.
The bias and buffer stage
As the name suggests All Q ,C and ZD the Bias and buffer phases. Its main goal is to provide a stable MOSFET Gates and offset voltage and the voltage buffer amplifier stage of the High Resource capacity. What would have without the phase response and the effect
Slew rate is indeed very bad. The flip side of the coin is not the extra step
Introduction of an additional dominant pole in the amplifier feedback loop.

500w audio amplifier circuit diagram pcb,simple mosfet amplifier circuit,200 watt mosfet amplifier circuit,300w audio amplifier circuit diagram,12v mosfet amplifier circuit diagram,400w audio amplifier circuit diagram pdf,100w mosfet amplifier circuit diagram,mosfet amplifier circuit for subwoofer,

Read More...

12/03/2017

HIFI Headphone Amplifier Circuit Diagram

Leave a Comment

HIFI Headphone Amplifier Circuit Diagram

This 1-watt amplifier leads itself par excellence for usa as driver for a low impedance headphone or as output stage in a hi-fi preamplifier driving an active loudspeaker. The schematic of this amplifier consists of an opamp type LF356 and a push-pull transistor output stage. Low-pass filter R1/C2 at the input limits the slew rateof the input signal. The fixed quiescent current of 30 mA draw by the output transistors, and set by diodes D1…D4 in conjuction with emitter resistors R7 and R8, ensures very low crossover distorsion.
HIFI Headphone Amplifier Circuit Diagram
HIFI Headphone Amplifier Circuit Diagram


Feedback resitors R3 and R4 fix the gain at about 15dB. The consequent overall distortion with a 3dB bandwidth from 10 Hz to 30 Hz is only 0.1 percent.
The amplifier delivers a maxiumum powder of 1 watt into 8 ohm for an input signal of about 500 mV rms. High-impedance headphones and 4 ohm loudspeakers may also be connected withoutdetriment.
The amplifier is best build on the printed circuit boar shonw bellow. The two transistors (BD139, BD140) shoud be mounted on heat sinks - do not forget the insulating washers and the head conducting paste!

To drive high-imperdance headphones at high volume, you need a +/- 15 volts regulated powder supply

Searches related to hifi headphone amplifier circuit diagramheadphone amplifier circuit using op-amp,simple headphone amplifier circuit,stereo headphone amplifier circuit,build your own headphone amp,ne5532 headphone amplifier circuit,how to make your own headphone amplifier,simple headphone circuits,headphone amplifier circuit design,


Read More...

11/28/2017

Audio Power Amplifier IC LM Series

Leave a Comment

Audio Power Amplifier 170W LM4651

The combination of the LM4651 driver IC and the LM4652 power MOSFET Class D power amplifier IC provides a high efficiency amplifier solution, suitable for self-powered speakers, subwoofers and quality car boosters.

The LM 4651 is a fully integrated conventional pulse width modulator (PWM) driver, containing undervoltage, short circuit, overmodulation, and thermal shutdown protection circuitry. The IC features a standby function which shuts down the pulse width modulation, minimizing supply current.

The LM 4652 is a fully integrated H-bridge Power Mosfet IC in a TO220 power package. The IC has a built in temperature sensor to alert the LM4651 when the die temperature exceeds the threshold limit.

Used together, the LM4651 and LM4652 form a simple, compact, efficient, high quality power audio amplifier solution complete with protection, normally seen only in Class AB amplifiers.



The maximum efficiency of this circuit is 85% at 125W with a standby attenuation greater than 100dB. The THD at 10W, 4 ohms, 10 - 500Hz is max. 0.3%. The supply voltage can not exceed ± 22V.



For the best performance a suitable preamplifier is required. With the addition of a preamplifier the gain of the power stage can be greatly reduced to improve performance. The gain should be set to 10 V/V allowing for low gain on the Class D stage with a total system gain high enough to be a complete solution for line level sources.

The input filter used here does not noticeably increase THD performance but will help to maintain a flat frequency response as the Q of the output filter changes with load impedance.



Do not attempt to build this amplifier as your first project! Class D high power amplifiers are expensive, difficult to build and a very small error during assembly can lead to total devastation of the power IC or other costly components.

Searches related to Audio Power Amplifier

home audio amplifier
audio power amplifier ic
amplifier for home speakers
what is power amplifier
audio power amplifier circuit
audio amplifier circuit
power amplifier price
power amplifier wiki

Read More...

11/22/2017

Subwoofer Filter Circuit Diagram

Leave a Comment
General Description    
   This subwoofer active filter circuit is a 24 dB octave filter with a Bessel character and cutoff frequency of 200 Hz. So, if you are interested in experimenting with audio circuits in subwoofer range, this circuit is for you. In subwoofer range, all audio frequencies below 200 Hz can be fed to a single speaker box since the human directional perception of sound diminishes at this frequency range. The normal stereo signals above 200 Hz can be fed to 2 satellite speakers. How does the subwoofer filter works: A1 and A2 buffer the signals coming from right and left channels. Opamp combinations A2/A4 and A9/A10 function as the highpass filters. The outputs are then connected to the final amplifiers of the battelite boxes. Signals from both channels are fed to A5. Opamps A6/A7 function as the lowpassfilter, A8 as the output amplifier for the subwoofer signal. The signal level can be balanced between the subwoofer and the satellite lines. The power needed for this filter circuit must ne a symmetrical power supply. The opamps can have either JFET or bipolar inputs.

Cicuit Diagram
Subwoofer Filter Circuit Diagram
Subwoofer Filter Circuit Diagram

subwoofer filter circuit for tda7294,
subwoofer preamp circuit diagram,
subwoofer filter circuit using lm324,
subwoofer filter circuit using op-amp tl072,
subwoofer filter board,
diy low pass filter for subwoofer,
subwoofer filter kit,
transistor subwoofer circuit diagram,

Read More...

11/08/2017

Car Subwoofer Amplifier Circuit Diagram

Leave a Comment
Circuit Description:
This unit is intended to be connected to an existing car stereo amplifier, adding the often required extra “punch” to the music by driving a subwoofer. As very low frequencies are omnidirectional, a single amplifier is necessary to drive this dedicated loudspeaker. The power amplifier used is a good and cheap BTL (Bridge Tied Load) 13 pin IC made by Philips (now NXP Semiconductors) requiring a very low parts count and capable of delivering about 22W into a 4 Ohm load at the standard car battery voltage of 14.4V.
The stereo signals coming from the line outputs of the car radio amplifier are mixed at the input and, after the Level Control, the signal enters the buffer IC1A and can be phase reversed by means of SW1. This control can be useful to allow the subwoofer to be in phase with the loudspeakers of the existing car radio. Then, a 12dB/octave variable frequency Low Pass filter built around IC1B, Q1 and related components follows, allowing to adjust precisely the low pass frequency from 70 to 150Hz. Q2, R17 and C9 form a simple dc voltage stabilizer for the input and filter circuitry, useful to avoid positive rail interaction from the power amplifier to low level sections.

Circuit diagram:
Parts circuit:

P1_____________10K Log Potentiometer
P2_____________22K Dual gang Linear Potentiometer
R1,R4___________1K 1/4W Resistors
R2,R3,R5,R6____10K 1/4W Resistors
R7,R8_________100K 1/4W Resistors
R9,R10,R13_____47K 1/4W Resistors
R11,R12________15K 1/4W Resistors
R14,R15,R17____47K 1/4W Resistors
R16_____________6K8 1/4W Resistor
R18_____________1K5 1/4W Resistor
C1,C2,C3,C6_____4µ7 25V Electrolytic Capacitors
C4,C5__________68nF 63V Polyester Capacitors
C7_____________33nF 63V Polyester Capacitor
C8,C9_________220µF 25V Electrolytic Capacitors
C10___________470nF 63V Polyester Capacitor
C11___________100nF 63V Polyester Capacitor
C12__________2200µF 25V Electrolytic Capacitor
D1______________LED any color and type
Q1,Q2_________BC547 45V 100mA NPN Transistors
IC1___________TL072 Dual BIFET Op-Amp
IC2_________TDA1516BQ 24W BTL Car Radio Power Amplifier IC
SW1____________DPDT toggle or slide Switch
SW2____________SPST toggle or slide Switch capable of withstanding a current of at least 3A
J1,J2__________RCA audio input sockets
SPKR___________4 Ohm Woofer or two 8 Ohm Woofers wired in parallel

Technical data:

Output power (1KHz sinewave):
22W RMS into 4 Ohms at 14.4V supply
Sensitivity:
250mV input for full output
Frequency response:
20Hz to 70Hz -3dB with the cursor of P2 fully rotated towards R12
20Hz to 150Hz -3dB with the cursor of P2 fully rotated towards R11
Total harmonic distortion:
17W RMS: 0.5% 22W RMS: 10%
Original article sourse: eeweb.com

Searches related to car subwoofer amplifier circuit diagram
car subwoofer amplifier circuit diagram pdf
subwoofer circuit diagram free download
la4440 subwoofer circuit
5.1 subwoofer circuit diagram
low pass subwoofer circuit diagram
transistor subwoofer circuit diagram
subwoofer circuit diagram pdf
4558 ic subwoofer circuit


Read More...

Subwoofer Filter Circuit Board

Leave a Comment

Cheap car subwoofer filter circuit description:

     This subwoofer filter set Suitable for use with a great car audio system. Since this circuit is designed to operate with a 12 volt DC power. But if you put it to use with a home stereo, It do not have any rules. This subwoofer circuit set is designed to has a cut off frequencies of 200 Hz. If you are not satisfied, you can change the C6, C7, C8, new, follow the table below.
      The left cannel input signal is entered pass through capacitors C1, C3 are the output Signal to the original circuit. (Or rear left in the car). And the right cannel input signal is entered to C2, C4 to the original circuit. (Or rear right in the car). Two resistors R1 and R2 will be mixer audio signal the left channel and the right channel both together. Then next wire connects to C5. This capacitor is also know as the coupling capacitor to inverting input of M5218A (IC1a). The VR1 serves as a set of IC1a gain with much or less as you want.
     The output signal is entered pass through the low pass filter circuit that consists of R5, R6, R7, R8, C6, C7, C8 and IC1b Which will allow low frequencies under 100 Hz passed away only. And the output from pin 1 of IC1b is entered to pass through R9, C9 on to the power amplifier circuit that be designed for driver only the subwoofer loud speaker We use the LM7812 IC2 as 12V dc fixed regulator for this circuit so can use the voltage supply range 12Vdc to 24Vdc as we want. The diode D1 is protector connection voltage supply that wrote terminal that it can damage the IC1.

Cheap car subwoofer filter circuit diagram:

Cheap car subwoofer filter pcb layout:


Cheap car subwoofer filter circuit partlist:

IC1_______________________________M5218A
IC2_______________________________LM7812 IC-regulator 12V
R1, R2, R3_______________47K_______Resistor 1/4W 1%
R4, R5, R6, R7, R10_______10K_______Resistor 1/4W 1%
R8______________________20K_______Resistor 1/4W 1%
R9______________________100 ohm__ Resistor 1/4W 1%
C1, C2, C3, C4, C5________ 4.7uF 63V _see text
C6______________________0.33uF 63V see text
C7______________________0.27uF 50V see text
C8______________________0.027uF 50V see text
C9, C10__________________10uF 16V see text
C11_____________________0.1uF 63V see text
C12_____________________ 100uF 16V Electrolytic Capacitors
C13_____________________ 100uF 25V Electrolytic Capacitors

Searches related to subwoofer filter circuit board

subwoofer filter circuit diagram,
subwoofer filter kit,
subwoofer filter circuit using op-amp tl072,
subwoofer filter circuit for tda7294,
subwoofer filter circuit using lm324,
subwoofer preamp circuit diagram,
diy low pass filter for subwoofer,
simple subwoofer circuit diagram,

Subwoofer Filter Circuit Board

Read More...

11/07/2017

LM4702 Amplifier Circuit Diagram

Leave a Comment

LM4702 general description:

     The LM4702 is a high fidelity audio power amplifier driver designed for demanding consumer and pro-audio applications. Amplifier output power may be scaled by changing the supply voltage and number of output devices. The LM4702 is capable of delivering in excess of 300 watts per channel single ended into an 8 ohm load in the presence of 10% high line headroom and 20% supply regulation. The LM4702 includes thermal shut down circuitry that activates when the die temperature exceeds 150°C. The LM4702's mute function, when activated, mutes the input drive signal and forces the amplifier output to a quiescent state. The LM4702 is available in 3 grades that span a wide range of applications and performance levels. The LM4702C is targeted at high volume applications. The LM4702B includes a higher voltage rating along – LM4702A (1) (in development): with the tighter specifications. The LM4702A(1) (in ±20V to ±100V development) is the premium part with the highest voltage rating, fully specified with limits over voltage – LM4702B: ±20V to ±100V and temperature, and is offered in a military 883 – LM4702C: ±20V to ±75V compliant TO-3 package.

LM4702 features:

  • Very High Voltage Operation
  • Scalable Output Power
  • Minimum External Components
  • External Compensation
  • Thermal Shutdown and Mute

LM4702 applications:

  • AV Receivers
  • Audiophile Power Amps
  • Pro Audio
  • High Voltage Industrial Applications

LM4702 circuit diagram:

Typical Audio Amplifier Application Circuit

LM4702 layout and pcb:

LM4702 layout


LM4702 bottom pcb
LM4702 top pcb


Блок питания усилителя

LM4702 Audio Power Amplifier Datasheet - Download


Searches related to LM4702 Amplifier Circuit Diagram

lm4702 bridge amplifier   
lm4702 pcb
lm4702 price
lm4702 equivalent
lm4702 replacement
lm4702 datasheet
1000 watts power amplifier schematic diagram
lm4702 mosfet amplifier

Circuit Archives - Amplifier Circuit Design

Audio Power Amplifier Driver
Audio Power Amplifier Series Stereo High Fidelity 200 Volt ...
MOSFET Bridge Power Amplifier - Forum for Electronics
Read More...

11/06/2017

TDA7265 subwoofer circuit diagram

1 comment

TDA7265 description:

     The TDA7265 is class AB dual Audio Amplifier assembled in the multi watt package specially designed for high quality sounds application as Hi-Fi music centers and stereo TV sets

TDA7265 features:


  • WIDE SUPPLY VOLTAGE RANGE (UP TO±25V ABS MAX.)
  • SPLIT SUPPLY
  • HIGH OUTPUT POWER 25 + 25W @ THD =10%, RL = 8Ω, VS = +20V
  • NO POP AT TURN-ON/OFF
  • MUTE (POP FREE)
  • STAND-BY FEATURE (LOW Iq)
  • SHORT CIRCUIT PROTECTION
  • THERMAL OVERLOAD PROTECTION

TDA7265 amplifier circuit:

TDA7265 amplifier circuit

TDA7265 pcb

Searches related to TDA7265tda7265 amplifier circuittda7265 voltagetda7265 subwoofer circuit diagramtda7265 pcb layouttda7265 equivalenttda7265 single supplytda7265 power supplytda7265 amp circuitThe TDA7265 is class AB Dual Audio Power amplifier assembled in the @ Multiwatt package, specially designed for high quality sound application as Hi-Fi 

Read More...

11/01/2017

TDA2030 Audio Amplifier 1 x40W

5 comments

TDA2030 general description: 

    Although there are a number of hybrid output modules on the market, very few of them combine compactness with reasonable price and good performance. One of these few is SGS's used in the present amplifier. The design of the amplifier is straightforward: a power op-amp followed by two output transistors. The audio signal is applied to the non-inverting input of power op-amp IC1 TDA2030 via socket K1 and capacitor C1. The supply current to the IC varies in accordance with the input signal. Consequently, there will be a similarly varying voltage drop across resistors R6, R7, R8, and R9 since these are in the supply lines to the op-amp. As long as the current is lower than about 1A, the voltage drop across the resistors will be insufficient to switch on transistors T1 and T2. This means that outputs up to 2 W into 4 ohm are provided entirely by the op-amp. Once the output current exceeds a level of 1A, the transistors are on and contribute to the power output.
When the Input signal is small, there no quiescent current through the transistor, but there is through the op-amp. Crossover problems are thus obviated. Since the IC also provides thermal compensation, stability of the operating point is ensured.
The supply voltage may lie between 12 V and an absolute maximum of 44 V. Construction of the amplifier on the printed-circuit board should be straightforward. The transistors as well as the IC must be fitted insulated on to a heat sink of about 2 k W. Use plenty of heat conducting paste. The supply line should be protected by a 3.15 A fuse. You can use BD911, BD912 for T1 and T2.

TDA2030 Technical Data:


  • Supply voltage  - 44 V
  • Maximum output - 22 W into 8 Ohm
  • Maximum output - 44 W into 4 Ohm

TDA2030 Circuit diagram:

 
TDA2030 circuit diagram

TDA2030 pcb layout:

TDA2030 pcb and layout

TDA2030 parts list:

Resistors:
  • R1-R4 - 100 KOhm
  • R5 - 8.2 KOhm
  • R6 - R9 - 1.4 Ohm, 1%
  • R10 - 1 Ohm

Capacitors:
  • C1 - 470 nF
  • C2 - 10 uF, 63 V, radial
  • C3 - 4.7uF, 63 V, radial
  • C4,C5,C7 - 220 nF
  • C6 - 2200 uF, 50 V, radial
  • C8 - 100 uF, 50 V, radial

Semiconductors:
  • D1, D2 - 1N4001
  • T1 - BD712
  • T2 - BD711
  • IC1 - TDA2030
Datasheet for TDA2030: Download

Searches related to TDA2030


tda2030 circuit,
tda2030 power supply,
tda2030 subwoofer amplifier circuit,
tda2030 pinout,
tda2030 ic,
tda2030 price,
tda2030 pdf,
tda2030 pin configuration,

Read More...

10/31/2017

LM1875 AUDIO AMPLIFIER 20W

Leave a Comment

LM1875 general description:



LM1875 pcb layout
LM1875 pcb layout
The LM1875 is a monolithic power amplifier offering very low distortion and high quality performance for consumer audio applications. The LM1875 delivers 20 watts into a 4Ω or 8Ω load on ±25V supplies. Using an 8Ω load and ±30V supplies, over 30 watts of power may be delivered. The amplifier is designed to operate with a minimum of external components. Device overload protection consists of both internal current limit and thermal shutdown.The LM1875 design takes advantage of advanced circuit techniques and processing to achieve extremely low distortion levels even at high output power levels. Other outstanding features include high gain, fast slew rate and a wide power bandwidth, large output voltage swing, high current capability, and a very wide supply range. The amplifier is internally compensated and stable for gains of 10 or greater.


LM1875 amplifier circuit:

LM1875 AUDIO AMPLIFIER 20W
LM1875 AUDIO AMPLIFIER 20W

LM1875 power supply diagram:

LM1875 power supply diagram
LM1875 power supply diagram

LM1875 pcb layout:

LM1875 pcb layout
LM1875 pcb layout

LM1875 project review:


Searches related to AUDIO AMPLIFIER 20W

max9744 amplifier
max9744 adafruit
max9744 raspberry pi
20w class d amplifier
max9744 review
max9744 datasheet
arduino controlled audio amplifier

raspberry pi tube amplifier
Read More...

10/25/2017

100W Guitar Amplifier Schematic

Leave a Comment
Searches related to Guitar Amplifier
guitar amps brands
guitar tube amps
guitar amp amazon
guitar amplifier olx
guitar amplifier price
guitar amp reviews
cheap guitar amps
guitar amp marshall
guitar amplifier circuit diagram with pcb layout
simple guitar amp circuit
bass guitar amplifier circuit diagram
how to make a mini guitar amp
how to make 9 volt portable guitar amplifiers
guitar amp schematics free
solid state guitar amp schematics
esp amp


Read More...

TDA8947J Audio Amplifier 29W

1 comment

TDA8947J general description:

The TDA8947J contains four identical audio power amplifiers. The TDA8947J can be used as: four Single-Ended (SE) channels with a fixed gain of 26 dB, two times Bridge-Tied Load (BTL) channels with a fixed gain of 32 dB or two times SE channels (26 dB gain) plus one BTL channel (32 dB gain) operating as a 2.1 system The TDA8947J comes in a 17-pin Dil-Bent-Sil (DBS) power package. The TDA8947J is pin compatible with the TDA8944AJ and TDA8946AJ. The TDA8947J contains a unique protection circuit that is solely based on multiple temperature measurements inside the chip. This gives maximum output power for all supply voltages and load conditions with no unnecessary audio holes. Almost any supply voltage and load impedance combination can be made as long as thermal boundary

conditions (number of channels used, external heatsink and ambient temperature) allow it.


TDA8947J features:


  • SE: 1 W to 25 W, BTL: 4 W to 50 W operation possibility (2.1 system)
  • Soft clipping
  • Standby and Mute mode
  • No on/off switching plops
  • Low standby current
  • High supply voltage ripple rejection
  • Outputs short-circuit protected to ground, supply and across the load
  • Thermally protected
  • Pin compatible with TDA8944AJ and TDA8946AJ

TDA8947J applications:


  • Television
  • PC speakers
  • Boom box
  • Mini and micro audio receivers

TDA8947J amplifier diagram:



TDA8947J layout:




Searches related to TDA8947J:
tda8947j circuit diagram,
tda8947j equivalent,
tda8947j pinout,
tda8947j price,
tda8947j schematic,
tda8946j equivalent,
4 channel car amplifier circuit,
4 channel audio amplifier circuit diagram,
Read More...

10/24/2017

LX1720 Audio Amplifier 2x20W

Leave a Comment

LX1720 general description:

The LX1720 controller IC contains the necessary functions to implement a stereo Class-D audio amplifier. A Class-D amplifier is a "switching" amplifier that converts a low-level, analog, audio input signal into a highpower, pulse-width modulated (PWM) output. The switching frequency is much higher than the audio band which allows high frequency out-of-band components to be removed with a simple LC filter. The LX1720 generates a PWM output by controlling external MOSFET's connected in a full-bridge configuration. Because the MOSFET's are either full "on" or full "off", their power dissipation is minimal allowing maximum power to be delivered to the speaker.

LX1720 Circuit:

LX1720 Audio Amplifier 2x20W
LX1720 Audio Amplifier 2x20W

Read More...

10/10/2017

TDA8922 Audio Amplifier 2x25W

2 comments

TDA8922 general description:


The TDA8922 is a high efficiency class-D audio power amplifier with very low dissipation. The typical output power is 2 × 25 W. The device is available in the HSOP24 power package with a small internal heatsink and in the DBS23P through-hole power package. Depending on the supply voltage and load conditions, a very small or even no external heatsink is required. The amplifier operates over a wide supply voltage range from ±12.5 to ±30 V and consumes a very low quiescent current.


TDA8922 features:


  • High efficiency (∼90%)
  • Operating supply voltage from ±12.5 to ±30 V
  • Very low quiescent current
  • Low distortion
  • Usable as a stereo Single-Ended (SE) amplifier or as amono amplifier in Bridge-Tied Load (BTL)
  • Fixed gain of 30 dB in Single-Ended (SE) and 36 dB in
  • Bridge-Tied Load (BTL)
  • High output power
  • Good ripple rejection
  • Internal switching frequency can be overruled by an external clock
  • No switch-on or switch-off plop noise
  • Short-circuit proof across load and to supply lines
  • Electrostatic discharge protection
  • Thermally protected.

TDA8922 applications:


  • Television sets
  • Home-sound sets
  • Multimedia systems
  • All mains fed audio systems
  • Car audio (boosters).

TDA8922 amplifier diagram, circuit:


TDA8922 pcb layout:



Read More...